Designed for wear protection and restoring repair of engines parts of motor technique with working volume up to 1,000 cc.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12101

Harga :
Rp. 281.250,-/tube

A New metalloceramics coating is formed on the surfaces of friction pairs (engine parts increase in volume and restore their geometry). As a result the renovated unit surpasses the new one with its performance level and is guaranteed to serve 2-4 times longer.

• Restores and protects friction parts of the cylinder-piston group, crank- and gas-distributing mechanism from wear.
• Significantly reduces fuel consumption (up to 30% at idling).
• Increases oil pressure in the system to nominal one.
• Levels and increases compression in cylinder.
• Increases the power of the engine improves its acceleration.
• Decreases noise and vibration level by 10 times.
• Increases the life span of the units by 2-3 times.
• Protects the engine from negative consequences of cold starts.
• Improves the engine operation already after 50-100 km.
• Enables to run the engine up to 300 km in case of oil leakage.

For an engine with oil capacity of 3-10 liters.
Stage 1 : Squeeze out the contents of one tube into the oil filler neck of the engine warmed up to the working temperature. Start the engine and let it idle for 5-10 minutes.
Stage 2 : Repeat the procedure after 100-250 km run.
Stage 3 : Repeat the procedure after 100-250 km run after completing Stage 2.

Note :

• Oil must not be changed untill the end of the treatment.
• Treatment is considered to be finished after the mileage of not less than 1,500 km.
• Treatment can be done at idling (4 hours – is an equivalent of 200 km run).
• New engines with run about 20,000 km should be treated in one stage.
• Engines after overhaul are recommended to treat in a usual way in three stages.
• Treatment of engines working on liquefied gas is similar to the treatment process of gasolines engines.
• Protective metalloceramics coating is formed on any working mechanism, however, if the mechanism (engine) is in a critical condition (100% wear), the destroyed parts should be replaced.

Designed for wear protection and restoring repair of diesel engines without disassembling.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12102

Harga :
Rp. 300.000,-/tube

A New metalloceramics coating is formed on the surfaces of friction pairs (engine parts increase in volume and restore their geometry). As a result the renovated unit surpasses the new one with its performance level and is guaranteed to serve 2-4 times longer.

• Restores and protects friction parts of the cylinder-piston group, crank- and gas-distributing mechanism from wear.
• Significantly reduces fuel consumption (up to 30% at idling).
• Increases oil pressure in the system to nominal one.
• Levels and increases compression in cylinder.
• Increases the power of the engine improves its acceleration.
• Decreases noise and vibration level by 10 times.
• Increases the life span of the units by 2-3 times.
• Protects the engine from negative consequences of cold starts.
• Improves the engine operation already after 50-100 km.
• Enables to run the engine up to 300 km in case of oil leakage.

For an engine with oil capacity of 3-10 liters.
Stage 1 : Squeeze out the contents of one tube into the oil filler neck of the engine warmed up to the working temperature. Start the engine and let it idle for 5-10 minutes.
Stage 2 : Repeat the procedure after 100-250 km run.
Stage 3 : Repeat the procedure after 100-250 km run after completing Stage 2.

Note :

• Oil must not be changed untill the end of the treatment.
• Treatment is considered to be finished after the mileage of not less than 1,500 km.
• Treatment can be done at idling (4 hours – is an equivalent of 200 km run).
• New engines with run about 20,000 km should be treated in one stage.
• Engines after overhaul are recommended to treat in a usual way in three stages.
• Protective metalloceramics coating is formed on any working mechanism, however, if the mechanism (engine) is in a critical condition

Designed for wear protection and restoring repair of power steering pumps and other hydraulic equipment.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12104

Harga :
Rp. 218.750,-/tube

It is specially designed for revitalization of hydraulic equipment. A new metalloceramics coating is formed on the friction pairs. As a result, the renovated unit surpasses the new one with its performance characteristics and is guaranteed to serve 2-4 times longer.

• Decreases force on a steering wheel.
• Increases the pump performance.
• Increases the accuracy of the hydraulic system operation already after 50-100 km after application of the revitalizant.
• Decreases noise and vibration of the pump of the steering booster.
• Protects parts from wear at the reduced oil level.
• Eliminates pump howling.

Treatment of the unit with the hydraulic system capacity of 1-2 liters.

1. Check the working fluid level in the hydraulic booster tank.
2. Squeeze out the contents of one tube into the hydraulic booster tank.
3. After adding the revitalizant, rotate the steering wheel during 5-10 minutes.
4. Revitalization is completed after 50 hours of the mechanism operation (1,500 km run).

Note :

• The sure sign of revitalizing beginning is a decrease of noise in the mechanism from the first kilometers of run. If the improvement of mechanism operation stopped at some moment, it testified to extreme wear of the mechanism – the recommended dose should be doubled.
• If after 100-200 km run, no improvement in the mechanism operation is observed, then the most probable cause is a mistaken diagnostics.

Designed for restoring repair and further wear protection of the engine cylinder-piston group without disassembling.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12105

Harga :
Rp. 118.750,-/tube

Dosage :
1 cylinder – 1 tube

As a result of the gel application, the cylinder geometry is restored; its internal diameter is reduced; ellipse form disappears.

• Increases compressions.
• Restored cylinder geometry.
• Eliminates scratches and tearings of 0.1 mm size.
• Protects cylinders against wear at cold start.
• Decreases noises and vibrations.
• Increases engine power.
• Decreases fuel consupmtion.
• Reduces the content of CO and CH in exhausts.
• Selective repair is possible (treatment of one or several cylinders).

1. Warm up the engine to the working temperature.
2. Twist out the plug from the cylinder; disconnect the central cable of the sensor of ignition timing and switchboard.
3. For 2-stroke engines, put the piston to the upper “dead” point (to avoid the gel getting to inlet and exhaust ports).
4. Squeeze out the contents of one tube into the cylinder. Attentions! Squeeze out the contents of the tube onto the cylinder wall and not onto the piston.
5. Let the piston have 15-20 strokes (with a crank, towing, by rolling a driving wheel, when it is in the air, etc).
6. Twist in the plug and drive the starter 3-4 times for 3-4 sec with the break intervals for 15-20 seconds.
7. For 2-stroke engines, dissolve the contents of another tube in 5-10 ml of motor oil and pour into the fuel tank.
8. Attach the central cable and switchboard, and run the engine at the idle for 15 min.
9. Run the car in a usual mode.

Note :

• It is advised to use medical syringes with a hollow tube for nooks. The contents of the tube with the revitalizant can be dissolved in 5-10 ml of motor oil. To avoid hydraulic shock, the total amount of the fluid introduced to the cylinder shall not exceed 20 ml.
• With the diameter of the cylinder over 120 mm, the revitalization cycle should be repeated.

Designed for wear protection and restoring repair of Gear Boxes, Transfer Cases & Differentials

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12103

Harga :
Rp. 218.750,-/tube

The gel-revitalizant forms a new metalloceramics coating with unique characteristics on the surfaces of friction pairs and protects transmission friction parts (pinion gears and bearings) from wear.

• Restores geometry of the parts.
• Removes blebs and scratches on work surfaces.
• Optimizes contact patches in pinion engagement areas.
• Reduces noise and vibration level by 10 times.
• Increases accuracy of gear shift.
• Improves operation of synchronizers.
• Provides significant fuel economy (especially for all-wheel drive vehicles)
• Enables to run the transmission units (up to 1,000 km) in case of oil leakage.

Treatment of units with the oil capacity of 1-2 liters.

1. Squeeze out the contents of one tube into the oil filler neck of the gear box, transfer case or axle reducers.
2. The treatment is completed after 50 hours of the mechanism operation (1,500 km run).

Note :

• The sure sign of revitalizing beginning is improvement in the steering-wheel mecanism operation (steering-wheel force augmentation, operation accuracy and noise decrease) already after the first kilometers of run.
• If after 100-200 km run, no improvement can be observed in the hydraulic booster operation, then the most probable cause is a mistaken diagnostics.

Designed for wear protection and restoring repair of friction parts of fuel equipment in gasoline and diesel engines.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12108

Harga :
Rp. 218.750,-/tube

Specially designed for revitalization of fuel equipment: high-pressure fuel pumps of all types, unit-injectors, roller and gear pendulous assemblies of electric gasoline pumps. The high microhardness of contact patches, obtained as a result of the treatment, prolongs the service life of the fuel equipment and provides efficient protection against low-quality fuel.

• Restores geometry of the parts and protects friction parts of an fuel pump, injectors and unit injectors from wear.
• Effectively protects from low-quality fuel.
• Reduces fuel consumption.
• Increases engine power.
• Reduces noise and vibration.
• Decreases the amount of toxic components in exhausts.

1. Squeeze out the contents of 1 tube into the fuel tank with the minimum quantity of fuel.
2. Add 40-60 liters of fuel into the fuel tank.
3. Run the car as usual.
4. Revitalization is completed after approximately 100 hours of the mechanism operation (about 3,000 km run).

Note :

• It is advised to use medical syringes with a hollow tube for nooks. The contents of the tube with the revitalizant can be dissolved in 5-10 ml of motor oil. To avoid hydraulic shock, the total amount of the fluid introduced to the cylinder shall not exceed 20 ml.
• With the diameter of the cylinder over 120 mm, the revitalization cycle should be repeated.

For BARRELS OF RIFLED ARMS

Designed for restoring repair and wear protection of surfaces of any barrel bore of the rifled arms.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12107

Harga :
Rp. 175.000,-/tube

After application of the gel-revitalizant, the geometry of the barrel is restored. Improves shooting accuracy significantly. During a short period of time you can have a weapon of a higher class with a prolonged service life.

• Improves accuracy of hits by 80% with the target 100m away.
• Improves flatness of shots.
• Increases wear-resistance and durability of a barrel by 10 times.
• Imparts the weapon with the maximum destructive power.
• Restores and protects surfaces of the barrel bore from wear.
• Restores geometry of the barrel bore (complete obturation).

Stage 1 (10 shots)

1. Use the rifle brush to apply the red gel onto the inner barrel surface.
2. Apply the gel onto the bullet surface protruding out of the cartridge.
3. Make a shot.
4. Make at least 9 more shots having repeated steps 1 and 2.

Stage 2 (10 shots)

1. Make at least 10 shots with a preliminary treatment of the barrel bore and a bullet with yellow gel

Stage 3 (10 shots)

1. Make at least 10 shots using green gel.

Note :

• New barrels shall be treated with 10 shots using green gel.
• As a preventive measure for the restored barrels, it is recommended to make 10 shots with green gel after each 1,000 shots or at least once a year.

For COMPRESSORS AND BEARINGS

Designed for restoring repair and protection of industrial equipment against wear.

TECHNICAL CHARACTERISTICS
Main characteristics of metalloceramics coating :
- Microhardness – 750 kgf/mm2
- High corrosion stability
- Roughness Ra up to 0.06 µm

Package :
9 ml - tube in blister
Art. XA 12006

Harga :
Rp. 175.000,-/tube

Designed for wear protection and restoring repair of bearings in the oil bath as well as compressor units and parts of all types (except the oxygen ones). It prolongs the service life of units and mechanisms by 2-4 times and significantly reduces energy and resource consumption.

• Eliminates gaps and beat of bearings.
• Compressors obtain the nominal parameters much faster.
• Significantly decreases noise and vibrations.
• Decreases the consumption of energy carries during compressors operating.
• Stabilizes oil pressure.
• Decreases working temperature of units.

1. Squeeze out the contents of one tube into the oil filler neck of the compressor (unit) warmed up to the working temperature. Run the compressor (mechanism) as usual.
2. Follow the same application instructions after 8-12 hours of the compressor (unit) operation.
3. Follow the same application instructions after 8-12 hours of the compressor (unit) operation after Stage 2.